Author: Thomas Larsen

Introducing the CEMTEK KVB-Enertec Tunable Diode Laser (TDL) Model 7000 now certified for Ammonia (NH₃) to EPA Performance Specification 18 (PS-18) IP CEMS requirements modified for NH₃

Our Model 7000 NH₃ TDL is shown to meet Federal Performance Specifications PS-18 modified for NH₃ using Optical Integrated path CEMS.

Whether your application is a Gas Turbine, Coal Fired Boiler, Furnace, IC Engine, etc, you may now replace your troublesome differential NOx CEMS with our TDL whether its subject to PPS-001, PS-2 or any other Federal or State NH₃ Permit requirements. (More Info)

Sample lines are no different than other critical components in your CEMS. After ten years of service, you’re ready to replace it. Heated Sample Lines are essential to your CEMS performance.

Continuing changes in air quality regulations and the increasing complexity of emissions monitoring can make CEMS management difficult. CEMTEK KVB-Enertec can play a vital role in helping your company navigate this process by offering replacement components such as heated sample lines and providing the installation services that go along with it.

Heated sample lines ensure your sampled gases remain above the dewpoint which protects expensive components from corrosion and keeps important analytes from being lost.

Advances in low-level measurements for NO_x and CO require improved sample transport technologies.

1. New heating elements offer longer life and improved temperature stability.
2. Stainless steel sample tubing prevents the loss of measured constituents at very low levels.
3. Redundant thermocouples ensure maximum life from your sample line.

Contact TruWinR to discuss your options at 504-316-9527.

TruWinR Corporation is pleased to announce that they have been selected by Optical Scientific Incorporated to be their representative for Louisiana.

Optical Scientific designs and builds the most advanced optical instruments in the world for measuring, airflow, turbulence, and visibility. For over thirty years we have been engaged in a constant research and development program to ensure our position as world leader. Our sensors and systems serve chemical manufacturers, smelters, power plants, refineries, and hundreds of other commercial and industrial sites around the world.

Since 1985, OSI has installed thousands of flowmeter systems worldwide, offering a full range of services including installation and startup, system verification, performance testing services, and field training.

More info

TruWinR Corporation is pleased to announce that they have been selected by ADS-Accusonic to be their representative for Louisiana and Arkansas.

ACCUSONIC^® is the industry-leading , high performance flowmeter system used in the water, wastewater, and power generation markets.  ACCUSONIC systems employ the multi-path transit-time principle to measure flowrate in applications ranging from large diameter pipelines and tunnels, to open and closed channels, rivers, and canals. 

ACCUSONIC flowmeters are well known throughout the industry for their high accuracy, long-term reliability, and versatility in the most difficult applications. ACCUSONIC products and services help organizations earn additional revenue, meet strict safety and environmental requirements, and increase plant efficiencies, thus reducing operating costs and improving profitability.

Since 1967, ACCUSONIC has installed thousands of flowmeter systems worldwide, offering a full range of services including installation and startup, system verification, turbine performance testing services, and field training. ACCUSONIC is a brand of ADS LLC. 

More info

CEMTEK KVB-Enertec, Inc.

Innovative Emissions Monitoring
for Compliance and Process Improvement

---

Why Choose CEMTEK for Your CEMS Service Requirements?
The Benefits of a CEMTEK-KVB-Enertec Maintenance Contract

Continuing changes in air quality regulations and the increasing complexity of emissions monitoring can make CEMS management difficult. CEMTEK KVB-Enertec can play a vital role in helping your company navigate this process as well as achieve and maintain the quality environmental compliance data you need to meet your availability requirements!
All field service paperwork is carefully documented, collected, archived, and made available for any future needs (e.g., internal audits, air district inspections, etc.). Additionally, CEMTEK service can assist your company in maintaining your Quality Assurance Plan.

---

CEMTEK KVB-Enertec Maintenance Offers

• Service technicians located throughout the country for expedited service
• Service technicians experienced in servicing a wide range of analyzers, probes, sampling systems, and data acquisition systems
• Expert engineering and field service support
• CEMS hardware training
• DAHS training
• Quarterly audit and annual RATA assistance
• QA/QC Plan updates and modifications
• Part 75 monitoring plan updates and modifications
• EDR service contract options: reporting, data validation, and allowance tracking
• Special state and local reporting options
• RTU and RECLAIM data reconcilement program options
• EPA audit assistance
• Regulatory consulting and assistance
• Assistance in data interpretation
• 24/7 emergency call-out support
• Parts availability
• Single source responsibility
• Reliable and dependable on-site presence

---

Preventative Maintenance

Preventative maintenance visits are customized to meet the needs of each customer and each CEMS with quarterly or monthly visits recommended for most sites to ensure the highest availability. Experienced CEMTEK service personnel will perform periodic and preventive maintenance service including probe inspection and cleaning, air cleaning system checks (scrubber replacement and filter changes), diagnostic check on all analyzers, performance of the manufacturer’s recommended preventive maintenance on each analyzer and complete calibration.

CEMTEK KVB-Enertec Supports the Following Systems

Continuous Emissions Monitoring Systems (CEMS)
• Complete inspection to verify proper operation of entire system
• Perform leak checks on each system component
• Replace sample probe filters as required
• Replace sample conditioning filters as required
• Replace analyzer filters as required
• Rebuild analyzer sample pumps according to manufacturer’s recommendation
• Rebuild sample transport pumps according to manufacturer’s recommendation
• Verify zero air generator for proper operation
• Replace zero air generator filters/chemicals as required
• Perform manual calibrations as required
• Complete analyzer maintenance checklists
• Document and submit maintenance service visit reports

Continuous Emissions Rate Monitoring Systems (CERMS)
• Perform flow monitor flow and leak checks
• Verify the calibration of the output and re-calibrate if necessary
• Inspect cable connections on terminal strips and terminal blocks
• Inspect interconnecting cable and wiring
• Check the conductors for corrosion and replace if necessary
• Conduct leak check and replace any corroded seals as necessary
• Check the flow element for debris and clean as necessary
• Check and replace chemical absorbers as necessary
• Check pitot for alignment, plugging, and/or corrosion; adjust and replace if necessary
• Inspect transducers
• Inspect and change purge air filters as necessary
• Inspect and clean sender/receiver units
• Inspect purge air supply
• Clean filter housing
• Replace filter insert as necessary

Continuous Mercury Monitoring Systems (CMMS)
• Complete inspection to verify proper operation of entire system
• Perform leak check
• Replace sample probe filters as required
• Replace air clean up panel media and filters as required
• Replace analyzer filters as required
• Rebuild sample transport pumps according to manufacturer’s recommendation
• Perform manual calibrations as required
• Complete analyzer maintenance checklists
• Document and submit maintenance service visit reports

Continuous Opacity Monitoring Systems (COMS)
• Perform opacity monitor inspections and preventative maintenance
• Inspect/clean/replace purge air filter as required (supplied by customer)

Additional Services

Quarterly Audits
CEMTEK provides on-site Quarterly Audit assistance and will perform Cylinder Gas Audits per USEPA 40CFR Part 60, Appendix F or conduct Linearity Test Audits per USEPA 40CFR Part 75, Appendix B. The audit data will be included in quarterly reports for local reporting and the EDR’s for Part 75 reporting.

Annual Audits
For the Annual RATA, CEMTEK technicians will be on-site the day of pretest runs and the day of testing. The data will be included in reports for all required reporting.

USEPA EDR or SCAQMD RECLAIM Services
A one-year EDR service contract assures accurate and error free data. CEMTEK will retrieve data once per month via pcAnywhere or similar internet service as well at the end of each quarter. From our office, CEMTEK will validate data, run the EDR and then download the completed EDR and its associated history files to the site for your submittal to the EPA. CEMTEK will also partner with site personnel to coordinate linearity checks, RATA and so on. CEMTEK maintains and stores the history files and EDR’s at both our facility as well as the site facility computer. We can also provide a RTU and RECLAIM data reconciliation program.

Emergency Response: 24/7 Call-Out Support

Our technicians provide 24/7 call-out support, have extensive experience in the CEMS field, and are located throughout the country for expeditious dispatch. Emergency support also includes unlimited telephone support with one-hour callback times.

Check Out Our Other Exciting Features & Benefits!

Parts-Anytime, Anywhere
On-Site Training

Contact Us for Your Quote!
E-mail or call us 504-316-9527

Stay Connected
CEMTEK KVB-Enertec Inc. | 888-400-0200 www.cemteks.com
3041 S. Orange Avenue, Santa Ana, CA 92707
2849 Sterling Drive, Hatfield, PA 19440

Represented by TruWinR Corp, Metairie, LA
504-316-9527

The premier data acquisition and handling system for air emissions compliance. Our proven web-based platform has been meeting and exceeding regulatory compliance needs since 2003. The enhanced web interface found in the NetDAHS Edge software incorporates the innovative technology and tools necessary to monitor your air emissions data anytime, anywhere.

Leading Technology 
The ever-changing compliance needs of today’s environmental professionals require higher levels of automation and data accessibility. To respond to market demands, we designed the NetDAHS Edge software, a proactive and centralized control hub for air emissions compliance reporting. The software incorporates web-based push technology to allow accurate, live data from across your fleet to be shared among multiple users. The freedom of being able to access the DAHS from anywhere can allow an instruments and control technician to manage several tasks from a centralized location or the mobility to move on to the next the next location while one task finishes.

Software Evolution
CEMTEK KVB-Enertec is the exclusive provider of NetDAHS Edge software – the premier data acquisition and handling system for air emissions compliance and process improvement. Our proven web-based platform has been meeting and exceeding regulatory compliance needs since 2003 and continues to be an industry leader with the first successful emissions EDR submitted under the Mercury and Air Toxics Standards rule (MATS) in 2016. The enhanced web interface found in the NetDAHS Edge software incorporates the innovative technology and tools necessary to monitor your air emissions data anytime, anywhere.

Streamlined Compliance
A scalable platform that can be configured to handle 40 CFR 60/63/75 requirements along with state, local, or consent decree reporting obligations. A “One-Step EDR” button streamlines the quarterly reporting gauntlet by automating the checks on the hourly averages, data substitution routines and ultimately the creation of the electronic data report (EDR)

EDGE Trace
NetDAHS Edge includes an all-new feature set called EdgeTrace. Now when you want to understand more information about a widget displayed on a WorkSlate, you just hover over the widget name to display helpful information about the widget. This information can show the source of the data including any equations that combine information from other widgets.

EdgeTrace expands to provide more information about your alarms and episodes and can be configured to provide permit citations direct from your air permit for any episodes on your system. Once configured, all EdgeTrace text is fully customizable by the end user.

Cemtek Environmental Has Acquired KVB-Enertec

Cemtek Environmental is extremely excited to announce that we have acquired KVB-Enertec! KVB-Enertec is a Continuous Emissions Monitoring Systems (CEMS) and Data Acquisition and Handling Systems (DAHS) industry leader for over four decades operating in Hatfield, PA. This acquisition will allow Cemtek to offer a wider, more dynamic range of products and services and will enable growth in the emissions and gas monitoring for compliance and process improvement market place. The integration of both operations will ensure that all clients receive exceptional support, fast response times and first-rate products

New Name – Cemtek KVB-Enertec

With the addition of KVB-Enertec, Cemtek will now supply one of the best Part 60 and Part 75 DAHS and will allow Cemtek to be more competitive in the Emissions Monitoring Industry. This will enable us to provide a superior level of support for the Cemtek KVB-Enertec DAHS. Cemtek is committed to investing in research and development to add features and upgrades to the DAHS product while improving service and support to all of the existing and new DAHS clients.

Cemtek Environmental, Inc., a division of Cemtek Group, which includes Cemtek Systems and Cemtek Instruments is a leading supplier and integrator of custom engineered Continuous Emissions Monitoring Systems, Process Analytical Systems and provides support for compliance and non-compliance applications.

We warmly welcome KVB-Enertec and their clients into the Cemtek family. We look forward to serving you as Cemtek KVB-Enertec from today forward. 

Ty Smith

President